ALLESDICHT – The Liquid Rubber Seal from a Bucket AD "Auburn"
-
This product is currently unavailable.
/ - 0.13 Piece / m² x 2 mm
- (25.00 kg / Piece)
EAN: 4251469300187 | Item no.: 0018
ALLESDICHT – the liquid rubber seal from a bucket – is an innovative, water-based waterproofing compound for renovation, repair and new construction. The thick, brushable material is applied directly from the bucket and forms a seamless, elastic rubber skin upon drying. This provides long-lasting protection against penetrating or rising damp – even at complex details such as pipe penetrations, wall junctions or surface transitions.
Certified, solvent-free and eco-friendly
ALLESDICHT is approved with a general construction authority test certificate and meets the highest building standards. The ready-to-use dispersion is solvent-free, water-dilutable and pH-neutral (approx. 9) – skin-safe and low in emissions. Its main component is finely ground rubber granulate made from recycled tyres – a resource-saving and sustainable solution.
Wide range of uses – indoors and outdoors
Whether flat roof, metal roof, gutter, balcony, terrace, basement wall or shower: ALLESDICHT is suitable for horizontal and vertical waterproofing, both indoors and outdoors. It adheres to concrete, wood, bitumen, sheet metal, fibre cement, tiles, natural stone and many existing coatings – even on damp substrates.
Easy to apply – also for non-professionals
ALLESDICHT can be applied with a trowel, brush, roller or airless sprayer. Apply 2–3 coats “wet on dry”. For long-term effectiveness, a dry film thickness of 2–3 mm is recommended, which corresponds to a consumption of approx. 3.3 kg/m². The resulting membrane is flexible (approx. 200 % elongation) and bridges cracks (RÜ2-E / R2-B) – ideal for movement-prone substrates.
Durable, strong, dependable
The cured coating is watertight, airtight, abrasion-resistant and permanently elastic. It adheres with a tensile strength of up to 0.5 N/mm². ALLESDICHT can be processed at ambient temperatures between 5 °C and 30 °C and provides reliable long-term protection in a wide range of applications.
Product Highlights
Characteristics
Product Details – Material and Structure
Comparative values
If your gutter is leaking, any cracks or damaged areas can be easily sealed with WARCO's ALLESDICHT. ALLESDICHT is a flexible rubber powder sealant that is applied in several coats directly to the cleaned surface. When dry, it forms a durable, watertight rubber membrane that adapts perfectly to movement and remains stable even in extreme temperature fluctuations. This keeps your gutter watertight and protects your building from water damage.
Using ALLESDICHT from WARCO, a basement can be reliably waterproofed from both the inside and the outside – even retroactively. The seamless, permanently elastic rubber membrane formed by the processed and cured ALLESDICHT acts as a protective coating over the basement wall, effectively preventing moisture ingress. The viscous sealant is applied in several coats and, once dry, creates a highly elastic, completely waterproof rubber membrane that adheres optimally to the substrate and reliably bridges cracks caused by structural movements. ALLESDICHT can be applied by trowelling, brushing, or airless spraying on substrates such as concrete, masonry, or bitumen, ensuring long-lasting protection against moisture.
ALLESDICHT is ready to use and must be stirred thoroughly before application. Depending on the type and size of the area to be sealed, ALLESDICHT can be applied by brush, roller, trowel or spray. It is suitable for almost all common substrates such as concrete, wood, bitumen, tiles, etc. The substrate must be clean, dry and free from dust, oil and grease - highly absorbent surfaces can be pre-treated with a primer to improve adhesion.
ALLESDICHT is applied in two to three coats, each coat applied wet-on-dry to achieve the desired thickness of the finished rubber membrane (minimum 2-3mm). Each coat should be applied evenly and should not exceed a maximum thickness of 1.5mm. In areas of high stress, such as junctions and penetrations, reinforcement fabric can be used to provide additional strength. When fully cured, an elastic, waterproof rubber membrane is formed that provides reliable protection against moisture and, thanks to its excellent elasticity of 200%, is flexible enough to accommodate substrate movement.
To achieve reliable waterproofing, the fully dried ALLESDICHT rubber membrane must reach a minimum thickness of 2–3 mm. In practice, a dry film of 1 mm corresponds to a wet layer of 1.5 mm. In the ready-to-use delivered state, at least 3.0 mm to approximately 4.5 mm of ALLESDICHT must be applied.
ALLESDICHT is applied in two, three, or more working passes – each with a maximum wet layer thickness of 1.5 mm and always applied wet-on-dry. The exact number of coats depends on the structural requirements, the substrate, and the environmental conditions.
A properly executed building waterproofing system using ALLESDICHT offers long-lasting and reliable protection that consistently far exceeds the typical lifespan of other systems. The actual lifespan of the waterproofing depends on installation and usage conditions, such as mechanical stress, weather exposure, and the nature of the substrate.
Under favourable conditions, the ALLESDICHT waterproofing remains waterproof, elastic, and intact for decades. Thanks to its high elasticity and tear resistance, the ALLESDICHT rubber membrane easily accommodates structural movements and temperature fluctuations, and even protects against ponding water.
Once fully dried, ALLESDICHT can be easily overcoated with other materials such as paint, plaster, or screed. When applying the final layer of ALLESDICHT, the intended overlay should be taken into account by preparing the surface either smooth or textured. A rough rubber surface improves the adhesion of the subsequent coating, e.g., screed. However, it is absolutely essential that all ALLESDICHT layers are completely dry before the next material is applied.